Trafic shaping for site-to-site IPSec VPN (Zyxel USG 100 to Cisco PIX 501) DIR-655, DIR-835, etc., not passing VPN to VPN server. Forums → Equipment Support → Hardware By Brand →

Discuss: Cisco PIX 501 Firewall Sign in to comment. Be respectful, keep it civil and stay on topic. We delete comments that violate our policy, which we encourage you to read.Discussion threads Pix 501 site 10.0.10.0/24 NSA 3500 site 10.233.0.0/23. NSA shows in the logs the tunnel is established and a few packets show in/out on the stats part. If I get on a client from the PIX side I can ping the X0 (LAN) IP address of the NSA 3500. I'm not sure where to even start. First site-to-site tunnel I've worked with. PIX 501 Drops VPN My new 501 is up and running, but I seem to be experiencing some trouble with the VPN. I use the Cisco VPN Client (tried 5.0.01, 5.0.03, 5.0.04) with Vista Ultimate 32-bit. Pictured left: Cisco Pix 501 security appliance for firewalling and VPN connectivity, incl. site-to-site VPN (<=10MB/s). 133MHz AMD SC520 Processor, 16 MB RAM, 8MB Flash [inside view] Cisco's smallest security appliance PIX 501 is a solid device for building site-to-site IPSEC VPN tunnels with speeds of more then 3 MB/s.

contained in this document are taken from a CISCO PIX 501 device running firmware PIX Firewall Version 6.3(4), and an ASUS SL1000/SL500 running firmware 1.1.72A.410. 2 Network Setup This section describes how to setup the network to carry out the SL1000/SL500 and CISCO PIX 501 Network Configuration as illustrated in Figure 2.1. PC2: 10.64.3.11 WAN:

Im configuring a Cisco PIX 501 so the computers behind it can be accessed remotely over a VPN connection. So far, Ive been able to successfully establish a connection (using MS PPTP client on Connecting to Cisco PIX/ASA Devices with IPsec¶ Using IPsec to create a VPN tunnel between pfSense® router and a Cisco PIX should work OK. As always with IPsec, be sure that the Phase 1 and Phase 2 settings match up on both sides. If an acceptable transform set and policy are already in place, they may be used. If your pix has a recent OS version on it, make sure you get the Cisco VPN client 3.x or 4.x, that way you can use the vpnclient commands. (Note: the setup for the VPN clinet 3.x is exactly the same as the VPN client 3000) Make sure you use the following commands:! - cisco VPN client uses IPSEC by default, so allow it: sysopt connection permit

Physically the PIX 501 is just a bit larger than an external modem (although not quite as thick!). Cisco's customer support (both live & via the web) has been above average so far. The live TAC support reminded me of L.L. Bean, and the docs present on the web show a depth very few other tech sites can match (outside of corps like MSFT, IBM, etc).

Hi, we have a pix 501 6.3(4), a windows 2000 server. I want to configure the pix so that when i am out of the office i can access files(and be connected) on the server remotely (which sits behind the pix). all the users to access the server remotely have cisco vpn client, nortel vpn client, and the usuall windows vpn client. I need a hardware VPN client which supports the Microsoft RRAS VPN server configured on my server. Perhaps the Cisco PIX 501? · Can you explain more? What do you mean by Using the full-featured VPN capabilities of the Cisco PIX 501 Security Appliance, businesses can securely extend their networks across low-cost Internet connections to mobile users, business partners, and corporate networks worldwide. Solutions supported range from standards-based